SciELO - Scientific Electronic Library Online

 
vol.53 número2INCLUSION COMPOUNDS OF α-CYCLODEXTRIN WITH ALKYLTHIOLSSYNTHESIS AND STRUCTURE OF DICARBONYLDICHLORO{2-(DIPHENYLPHOSPHINEOXIDE)PYRIDINE}RUTHENIUM(II) índice de autoresíndice de materiabúsqueda de artículos
Home Pagelista alfabética de revistas  

Servicios Personalizados

Revista

Articulo

Indicadores

Links relacionados

Compartir


Journal of the Chilean Chemical Society

versión On-line ISSN 0717-9707

J. Chil. Chem. Soc. v.53 n.2 Concepción jun. 2008

http://dx.doi.org/10.4067/S0717-97072008000200006 

 

J. Chil. Chem. Soc, 53, N° 2 (2008), pages: 1477-1479

 

INTERCALATION OF POLYETHYLENE OXIDE IN LAYERED THIOPHOSPHATE OF BI AND SB

 

DOMINGO RUIZ LEÓN, ANTONIO GALDÁMEZ AND VÍCTOR MANRÍQUEZ*

Universidad de Chile, Facultad de Ciencias, Departamento de Química, Casilla 653, Santiago, Chile. *e-mail: vmanriqu@uchile.cl


ABSTRACT

The intercalation compounds Li0,43(PEO)2.4(H2O)1.4K0.57BiP2S6 and Li0.38(PEO)2.1(H2O)1.6K0.62SbP2S6 have been synthesized by the insertion of polyethylene oxide PEO in LiKMP2S6 (M=Bi, Sb), that contained Li+ and K+ exchangeable cations in their interlayer space. The polymer PEO is able to associate interlayer Li+ cation modifying the ionic conductivity of pristine phases. These intercalation compounds constitute a new family of intercalates in the thiophosphate of Bi and Sb with Polyethylene oxide as guest species. They have been characterized by powder X-ray diffraction, FTIR-Raman, DTA/TGA analysis and electrical conductivity measurements. The studied nanocomposite shows values of electrical conductivity (σi) of about 10-6 Ω-1 cm-1 at room temperature.

Keyword: Intercalation, Chalcogenides, Layered compound


 

INTRODUCTION

The quaternary chalcophosphate compounds AMXPyQzx containing Bi and Sb, have attracted the attention of many workers because of their interesting anisotropic physical properties as well as potential technological applications 1,2. The chalcophosphates of the type AMP2Q6 (A = alkaline metals, M = Sb, Bi and Q = S, Se) are materials that present the anions (P2Q6)4- that are coordinated to the metals A and M through the chalcogen atoms Q 1,3-4. An important characteristic of the Bi and Sb atoms, in solid phases, is the stereochemical localization of the ns2 electron pairs, which produces important variations in crystal structure, physical properties and electronic structure of the resulting materials. Thus, these materials possess different crystalline structures, presenting one-dimensional ID, two-dimensional 2D and three-dimensional 3D structures. The phases M4(P2Se6)3 (M = Bi, Sb) exhibit structures related to Pb2P2Se6 5, while the phase ß-Bi4(P2Se6)3 exhibits a three-dimensional (3D) structure 6, with groups BiSe8 and P2Se64-. The quaternary chalcophosphates KMP2Q6 (M=Bi, Sb and Q=S, Se) exhibit two-dimensional (2D) structures, where the potassium atoms are located in the interlayer 7-9. Measures of electric conductivity, carried out in Cs8M4(P2Se6)5, indicate behaviors of semiconductors material with values of electrical conductivity, σi, 10-9 S/cm at room temperature 10.

The revival of interest in layered materials is originates from the observation of unusual physical properties and anisotropy phenomena. Since the physical properties of these materials can be modified significantly by intercalation, this aspect in turn resulted in a renewed strong motivation in the area of synthetic chemistry, for the search after novel host-lattices and intercalation compounds 11.

An other hand, the intercalation of large molecule into layered compounds is a topic of great interest, due that the intercalates can have in some cases physical properties very different from those of the pure host lattice 12-13. The intercalation of organic polymers in layered inorganic host materials to form organic/inorganic nanostructures has focused increasing interest because such systems can show physical and chemical behaviour synergistically derived from both host and guest 12-13. The polyethylene oxide (PEO) is one of such polymer that has been successfully intercalated into layered structures such as montmorillonite14, V2Os 15 , MS2 (M = Mo, Ti)16, Mo0317, MPS3 (M = Mn, Cd, Ni, Fe)18.

In order to obtain new organic/inorganic composite with novel host lattice. We described here the ability of polyethylene oxide to be intercalated into the van der Waals gap of the lamellar LiKMP2S6 (M=Sb, Bi) in a topotactic process giving rise to air-stable intercalates.

EXPERIMENTAL

Preparation of Host compounds

The phases KMP2S6 (M = Bi, Sb) were synthesized by direct combination of the pure elements in stoichiometric proportions, with an excess of chalcogen and phosphorus (1% mass) to avoid the formation of impurity phases. The reaction mixtures were sealed in evacuated quartz ampoules, and heated at 1023 K for one week. After the reaction was completed, the reacted matter was slowly cooled to room temperature at the rate of 6 K/h. Homogeneous and well-crystallized materials were obtained after grinding and reheating at 1023 K for one week. The reaction product was washed with DMF/ethylenediamine (3:1) to remove the PyQz and Q. SEM-EDX analyses carried out on the samples confirmed their purity, homogeneity and stoichiometry

Preparation of Intercalation compounds

The intercalation of Li was success fully carry out by reaction of pure KMP2S6 (M=Bi, Sb) and Li2S in stoichiometric amounts, sealed in evacuated quartz tubes, and then heated at 723 K for 1 weeks. After the reaction was completed, the reacted matter was slowly cooled to room temperature. The intercalation of PEO was achieved by treatment of aqueous suspension of the intermediate compounds LiKMP2S6 phase with an acetonitrile solution of PEO under vigorous shacking (24 h. at room temperature). Finally, the resulting product was washed with acetonitrile and vacuum dried.

Characterization

Both the host- and intercalation compounds were characterized by EDX, XRD and FTIR-Raman. The elemental analyses were obtained by EDX and for all compounds described here. SEM-EDX analyses were obtained on a CAMECA SU 30 with detector PRINCETON GAMMA. The X-ray powder diffraction (XRD) data were collected at room temperature on a Siemens D 5000 powder diffractometer, with CuKα radiation in the range 5 < 2θ < 60°.

The infrared spectra were obtained in the range 4000 - 370 cm-1 on samples pressed into KBr disk using a Perkin Elmer FTIR-Raman spectrometer system 2000. All Raman spectra presented were recorded in Renishaw system 2000 in the range 3000-100 cm-1, using laser excitation at 633 nm He-Ne and laser power of 2.5 mW at the sample. All measurements were made in a back-scattering geometry, using a 50 x microscope objective with a numerical aperture value of 0.75, providing scattering areas (spatial resolution) of 1 µm2. Single point spectra were recorded with 4 cm-1 resolution and 10 s accumulation times.

The Differential Thermal analysis (DTA) and Thermal Gravimetric analysis (TGA) were performed on a STA 1500 H / 625 Thermal analysis system, Rhoeometric scientific. The DTA -TG curves were run simultaneously on each sample from room temperature at 1273 K, in flowing atmosphere of nitrogen using a heating rate of 10 K / min.

Electrical conductivity of the samples was measured by an ac and dc method on cylindrical disk samples, mounted between two gold electrodes. The ac conductivity measurements were carried out by an ac complex impedance analysis in the frequency range from 0.1 Hz to 10 MHz by Solartron SI 1260 Impedance /Gain Phase Analyser with a signal level 0.2 to 1 V. Direct current (dc) conductivity was determined by an Keithley 237 source-meter. The Ohmicity was checked, there was no evidence of any nonlinearity in the I-V characteristics. All the measurements were found to be reproducible.

RESULTS AND DISCUSSION

It is know that cations could be intercalated into layered phases such as AMPS3 (A=Na, K and M=Mn, Fe, Ni, Cd) following an ion-exchange process in which the alkaline ions are replaced 19-20. However all attempts to intercalation of Li+ into KMP2S6 (M=Bi, Sb) host matrix by ion-exchange reaction from salt aqueous solutions failed. The partial intercalation of Li+ was success carried following the procedure by the low temperature topotactic solid-solid ion-exchange reported by M.G. Kanatzidis et al. 21, where the K+ ions are replaced by the smaller cations Li+ according with:

The treatment of the KMP2S6 compounds with Li2S results in a partial K+ - Li+ exchange, this leads to the desire intercalated materials with a small cations. We noted that the interplanar spacing calculated from XRD patterns is very close to the values for the pure starting KMP2S6 host matrix, we have previously reported the crystal structure of the phases KMP2S6 (M=Bi, Sb), which are shows in figure 1 8-9. The values of the basal spacing, such as the ir spectra, are consistent with the size of the cationic guest species Li+. In addition the presence of lithium is noticed in the Raman spectra essentially by a new weak band which is located at 323 cm-1 (Fig. 2). This new peak is interpreted as a stretching mode due to vibration of Lithium atoms located in the van der Waals gap against the nearest neighbouring sulphur atoms like LiS6 entities 22. Finally, according to elemental analysis, the intercalation compounds prepared may be formulated as Li0.43K0.57BiP2S6 and Li0.38K0.62SbP2S6.



The kinetics of intercalation of organic polymers into layered compounds is generally unfavourable due to the high activation energy associated with the deformation of the crystal structure of the inorganic host species. Thus, the insertion process requires the expansion of the interlayer spacing by a previous intercalation of simple small hydrated ions 23. The Li(PEO)KMP2S6 nanocomposite was obtained by reaction of the intermediate LiKMP2S6 with PEO. To swell the layers apart, we form, in a first step, an aqueous suspension of LiKMP2S6. The stoichiometry of the final products Li0.43(PEO)2.4(H20)1.4K0.57BiP2S6 and Li0.38(PEO)2.1(H O)1.6K0.62SbP2S6 were determined by elemental analysis and thermal gravimetric measurement. The Tables 1 and 2 summarizes the analytical data for the obtained intercalation compounds, slight deviations from the ideal composition may reflect some heterogeneity of the samples. The studied nanocomposite show a mass losses of 8.3% below 200°C and 41.6% at 320°C, which are ascribed to dehydration and PEO decomposition, respectively. The material is thermally stable under nitrogen up to 260°C.




The PEO intercalated composites were characterized by X-ray powder diffraction (XRD). The XRD patterns of the intercalate shows a significant loss of crystallinity, compare with pristine KMP2S6 with sharp 001 reflection which yield an interlamellar distance of 14.5Å. The Fig. 3 shows the XRD pattern of Li0.43PEO2.4H2K0.57BiP2S6 compared with pristine Li0.43K0.57BiP2S6. The basal spacing increases found can be interpreted as the intercalation of PEO with helical conformation, or as a two-layer arrangement of PEO chains in a zigzag conformation.


The IR spectra of the intercalates (Fig. 4) shows some characteristic bands attributed to CH2CH20 groups (Table 3) and display two strong bands at 598 and 495 cm-1 arising from the splitting of the v(PS3) stretching band occurs at 570 cm-1 in pristine KMP2S6. The splitting reflects the presence of intralamellar guest species 24. The broad Strong band centered a 2890 cm-1 in bulk PEO, associated with CH2 stretching modes appears in the intercalate form like two weak bands at 2855 and 2929 cm-1. This behaviour is commonly found in other PEO nanocomposites and has been ascribed to interactions between oxygen atoms in PEO and interlayer cation 25. Both XRD and IR data confirm the intercalation of PEO in LiKMP2S6 (M=Bi, Sb) host matrix.




The experimental stoichiometry is around two CH2CH20 units per LiKMP2S6 formula, suggesting that the arrangement is less dense than a double layer of linear zig zag like PEO chains. Thus, the PEO chains solvating the Li+ ion may exhibit a helical structure similar to that found in the corresponding PEO intercalates into MPS3 (M = Mn, Cd)18 and for the PEO-Lithium salt solid electrolytes26. It is reasonable to assume that solvation of the Li+ ion by the oxygen atoms of the polyethylene oxide is the driving force of the polymer insertion process.

The electrical conductivity was measured at room temperature, with samples under dry N2 flow. A.c. impedance data were obtained in the 105 -10-2 Hz range. Typical complex impedance plane plots show an arc (Nyquist diagram) displaced from the origin (Fig. 5). The total resistance is deduced from the intercept of the arc with the real axis at the lowest frequency values. Direct current (dc) measurements were performed, to ascertain the existence of slow relaxation mechanisms that may not be accessible through the impedance measurements.


The electrical conductivity at room temperature of KMP2S6 is ca. 10-7 S/cm. The intercalation of PEO also produce an enhance of the conductivity associated with ionic-conductivity to values, at room temperature, 10-6 S/cm (dc measurements). In addition it can be seen that the electrical conductivity is sensitive to other ionic species, as H30+, present in the system (Table 4).


ACKNOWLEDGMENTS

The authors wish to dedicate this work to the memory of Dr. Jaime Retuert, a fine Professor and a very good friend. This work was supported by FONDECYT grant N° 1061116

REFERENCES

1. M.G. Kanatzidis, Curr. Opinion Solid State Mater. Sci. 2, 139, (1997).        [ Links ]

2. a) M. A. Gave, D. Bile, S.D. Mahanti, J. D. Breshears an M. Kanatzidis, Inorg. Chem. 44, 5293, (2005).        [ Links ]

b) A. Galdámez, V. Manriquez, J. Kasaneva and R. E. Ávila, Mater. Res. Bull. 38, 1063, (2003).        [ Links ]

3. T. McCarthy, M. Kanatzidis, J. Alloys Compd. 236, 70, (1996).        [ Links ]

4. J. Breshears and M. Kanatzidis, J. Am. Chem.Soc. 122, 7839, (2000).        [ Links ]

5. M. Ruck, Z. Anorg. Allg. Chem. 621, 1344, (1995).        [ Links ]

6. J. Aitken, S. Brown, K Chondroudis, S. Jobic, R. Bree and M. Kanatzidis, Inorg. Chem. 38, 4795, (1999).        [ Links ]

7. T. McCarthy and M. Kanatzidis, Chem Commun. 1089, (1994).        [ Links ]

8. V. Manriquez, A. Galdámez, D. Ruiz-León and M.T. Garland, Z. Krist-New Cryst. St. 218, 151, (2003).        [ Links ]

9. V. Manriquez, A. Galdámez, D. Ruiz-León, and M.T. Garland, Z. Krist-New Cryst. St. 218, 403, (2003).        [ Links ]

10. T. McCarthy, T. Hogan, C. Kannnewurf and M. Kanatzidis, Chem. Mater. 6, 1072, (1994).        [ Links ]

11. R. Clement, L. Lomas and J.P. Audiére, Chem. Mater. 2, 641, (1990).        [ Links ]

12. L. Lomas, P. Lacroix, J.P. Audiére and R. Clement, J. Mater.Chem. 1,475, (1991).        [ Links ]

13. E. Rmz-Hitzky, Adv. Mater. 5, 334, (1993).        [ Links ]

14. P. Aranda, E. Ruiz-Hitzky, Chem. Mater. 4, 1395, (1992).        [ Links ]

15. E. Ruiz-Hitzky, P. Aranda, B. Casal, J. Mater. Chem. 2, 581, (1992).        [ Links ]

16. E. Ruiz-Hitzky, R. Jimenez, B. Casal, V. Manriquez, A. Santa Ana, G. González, Adv. Mater. 5, 738, (1993).         [ Links ]

17. L.F. Nazar, H. Wu, W.P. Power, J. Mater. Chem. 5, 1985, (1995).        [ Links ]

18. a) I. Lagadic, A. Le'austic, R. Clement, Chem. Commun. 1396, (1992).        [ Links ]

b) V. Manriquez, P. Barahona, D. Ruiz and R. Avila, Mater. Res. Bull., 40, 475, (2005).        [ Links ]

19. R. Clement, J. Am. Chem. Soc. 103, 6998, (1981).        [ Links ]

20. R. Clement, A. Leaustic, K. Marney and A.H. Francis, J. Phys.Chem. Solids 55, 9,(1994).        [ Links ]

21. K. Chondroudis and M.G. Kanatzidis, J. Solid State Chem. 136, 328, (1998).        [ Links ]

22. I. Kerrache, C. Julien, C. Sourisseau, Solid State Ionics 92, 37, (1996).        [ Links ]

23. R. Clement, O. Gamier and J. Jegoudez, Inorg.Chem. 25,1404,(1986).        [ Links ]

24. Y. Mathey, R. Clement, C. Sourisseau and G. Lucazeau, Inorg.Chem. 19, 2773, (1980).        [ Links ]

25. H. Lourdes, J. Morales and J. Santos, J. Solid State Chem. 141, 323, (1998).        [ Links ]

26. M. A. Ratner and D.F. Shriver, Chem.Rev. 88, 109, (1988).        [ Links ]

 

(Received: 26 November 2007 - Accepted: 6 March 2008)

 

Creative Commons License Todo el contenido de esta revista, excepto dónde está identificado, está bajo una Licencia Creative Commons